Call

The writer is making several good pointers on Installing A Bathtub as a whole in this post following next.

Setting up a bathtub isn't specifically rocket science, but it does call for strong plumbing, carpentry, and occasionally, tiling skills. Replacing an old tub with a brand-new one is likewise a moderately difficult project. If the old bathtub is easily accessible, the project can move quickly; if you have to open up a wall surface to eliminate the old bathtub and also position the brand-new tub, the job is much harder. In either instance, the project is within a home handyman's skills, although you will require an assistant to vacate the old tub and also embeded in the new one. Make sure you have actually qualified yourself for the work and are comfortable attempting it. Instead of employing a specialist to take over a halfway-completed task, it is much better to think about utilizing one prior to you start. Possibilities are you may need a professional plumber to make tube links.
This article will assist you set up a new bath tub in your bathroom if you have actually already bought a brand-new tub and do not need to transform the setup of your previous supply of water pipelines.
Your devices as well as product checklist need to comprise the following:

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipeline Caps


 

Removing Old Taps

If you require to change old taps with brand-new ones as a part of your installment, after that the first thing you ought to do is separate the water supply. After doing so, switch on the taps to drain pipes any water remaining in the system. The procedure of getting rid of the existing faucets can be fairly bothersome due to the restricted access that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the taps. Have a towel prepared for the staying water that will originate from the pipelines. As soon as the supply pipelines have been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary faucets from turning during this process. When the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned of any old sealing compound.
Before going on to fit the brand-new faucets, compare the pipe connections on the old taps to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new faucets to fit.

Fitting New Touches

If the tails of the brand-new taps are plastic, after that you will certainly need a plastic connector to avoid damage to the string. One end of the port fits on the plastic tail of the tap and the various other end gives a link to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the placing hole in the bath/basin making sure that the washers are in location between the tap and the sink. Safeguard the tap in place with the manufacturer offered backnut. When the faucet is securely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be connected by using corrugated copper piping or with regular faucet ports. The former type ought to be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.

Setting up the Tub

Using the two wood boards under its feet, put the bath tub in the needed setting. The wood boards are valuable in uniformly spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto four small factors.
The following objective is to guarantee that the bathtub is leveled all round. This can be accomplished by checking the level and also changing the feet on the tub until the level reviews degree.
To install faucets, fit all-time low of the furthest versatile faucet adapter to the proper supply pipeline by making a compression sign up with; after that do the same for the other tap.
Switch on the water as well as examine all joints as well as brand-new pipework for leakages and tighten them if essential. Fill up the bath tub as well as also examine the overflow outlet and also the normal electrical outlet for leakages.
Finally, fix the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and also securing around the bathtub needs to wait till the tub has actually been utilized at the very least once as this will certainly resolve it right into its final setting.

Preparing for the Setup

Firstly, the supporting structure supplied with the bath ought to be fitted (if needed) according to the supplier's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to see to it that if the tap features a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets device to avoid stress on the bath tub.
Fit the versatile tap connectors to the bottom of the two taps utilizing 2 nuts and olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet via the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you make use of every one of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath should currently prepare to be suited its last position.

Tiling Around the Tub

In the location where the bathroom meets the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is important as the installation can move enough to fracture an inflexible seal, creating the water to permeate the wall in between the bath and the tiling, bring about issues with moisture and feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to assimilate your fixtures as well as fittings. They are sold in tubes and cartridges, and are capable of securing voids up to a size of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with twists of drenched newspaper or soft rope. Remember to constantly fill up the bath tub with water before sealing, to allow for the movement experienced when the bathtub is in use. The sealant can break rather very early if you do not take into consideration this movement before securing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise quickly available on the market. It is suggested to fit the floor tiles using waterproof or waterproof glue as well as grout.

How to Install or Replace a Bathtub

Find Your Dimensions

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

 

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

Disconnect the Water Supply and Drain Assembly

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

 

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

 

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

Cut Out the Old Tub

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

 

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

 

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

Install the New Tub

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

 

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

 

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

 

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

Secure the Tub

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

 

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

 

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

 

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

We are very interested in A Step-by-Step Guide to Installing a Bathtub and I hope you appreciated the page. Sharing is caring. Helping others is fun. Thanks a bunch for your time. Don't hesitate to come visit our website back soon.

Appointment